Unlock Smooth Rotation: Master The Art Of Replacing A Kenmore Microwave Turntable Motor

If your Kenmore microwave‘s turntable is making a whirring noise or has stopped rotating altogether, you may need to replace the turntable motor. This is a relatively simple repair that you can do yourself with a few basic tools. In this blog post, we will provide step-by-step instructions on how to replace the turntable motor in your Kenmore microwave.

Tools and Materials Needed

• Phillips head screwdriver
• Flat head screwdriver
• Pliers
• New turntable motor (compatible with your Kenmore microwave model)

Step-by-Step Instructions

1. Unplug the Microwave: Before you begin any work on your microwave, be sure to unplug it from the power outlet. This will prevent any risk of electrical shock.

2. Remove the Outer Casing: Use the Phillips head screwdriver to remove the screws that secure the outer casing of the microwave. The location of these screws may vary depending on your microwave model. Once the screws are removed, carefully lift the outer casing off the microwave.

3. Locate the Turntable Motor: The turntable motor is typically located underneath the turntable. It is a small, round motor with a gear attached to it.

4. Disconnect the Turntable Motor: Use the pliers to disconnect the wires that are connected to the turntable motor. Be careful not to damage the wires.

5. Remove the Turntable Motor: Use the flat head screwdriver to pry the turntable motor out of its housing.

6. Install the New Turntable Motor: Place the new turntable motor into the housing. Make sure that the gear on the motor is properly aligned with the gear on the turntable.

7. Reconnect the Turntable Motor: Use the pliers to reconnect the wires to the turntable motor. Make sure that the wires are securely connected.

8. Reinstall the Outer Casing: Carefully replace the outer casing of the microwave. Secure it with the screws that you removed earlier.

9. Plug in the Microwave: Plug the microwave back into the power outlet.

10. Test the Turntable: Turn on the microwave and place a cup of water on the turntable. Start the microwave and observe the turntable. It should rotate smoothly and quietly.

Additional Tips

• If you are having difficulty removing the outer casing of the microwave, you may need to use a putty knife or a pry bar to help you.

• Be careful not to damage the wires when you are disconnecting and reconnecting the turntable motor.

• If you are not comfortable working on electrical appliances, you can always call a qualified appliance repair technician to replace the turntable motor for you.

Troubleshooting

If you have replaced the turntable motor but the turntable is still not rotating, there may be another issue with your microwave. Here are a few things to check:

• Make sure that the turntable is properly seated on the turntable drive shaft.

• Check the door switches to make sure that they are working properly.

• Check the control board to make sure that it is sending power to the turntable motor.

Wrapping Up

Replacing the turntable motor in your Kenmore microwave is a relatively simple repair that you can do yourself with a few basic tools. By following the instructions in this blog post, you can get your microwave up and running again in no time.

Answers to Your Most Common Questions

• Q: How do I know if my turntable motor needs to be replaced?

A: If your turntable is making a whirring noise or has stopped rotating altogether, you may need to replace the turntable motor.

• Q: Where can I find a replacement turntable motor for my Kenmore microwave?

A: You can find replacement turntable motors for Kenmore microwaves at most appliance parts stores or online retailers.

• Q: How much does it cost to replace a turntable motor in a Kenmore microwave?

A: The cost of a replacement turntable motor for a Kenmore microwave can vary depending on the model of your microwave. However, you can typically expect to pay between $20 and $50 for a new turntable motor.