How To Replace The Worm Gear In A Kitchenaid Mixer: A Simple Guide
What To Know
- You can order a new worm gear online, or you can take the mixer to a professional to have it repaired.
- Then, remove the screws that hold the worm gear in place and lift the old worm gear off of the drive shaft.
- Next, install the new worm gear by aligning the holes in the worm gear with the drive shaft and screwing the new worm gear into place.
A KitchenAid mixer is a kitchen staple, and with good reason. These mixers are known for their durability and performance. However, even the best mixer will eventually need repairs. One of the most frequent repairs that KitchenAid mixers need is the replacement of the worm gear. Luckily, this is a relatively easy repair that you can do at home with just a few tools.
How To Replace Kitchenaid Mixer Worm Gear
If your KitchenAid mixer‘s worm gear is worn out, it will need to be replaced. Here’s how to do it:
1. Unplug the mixer and disconnect it from the power source.
2. Remove the mixer’s bowl and attachment.
3. Disconnect the mixer’s drive shaft from the worm gear.
4. Remove the worm gear from the mixer.
5. Install the new worm gear.
6. Reconnect the drive shaft to the new worm gear.
7. Reinstall the bowl and attachment.
8. Plug in the mixer and test it to ensure that it is working properly.
If the worm gear is not the problem, you may need to check the mixer’s motor, belt, or transmission.
It is important to replace the worm gear as soon as possible to prevent further damage to the mixer.
You can order a new worm gear online, or you can take the mixer to a professional to have it repaired.
How To Access And Remove The Worm Gear From A Kitchenaid Mixer
- * Remove the screws and lift off the top
- * Disconnect the wires leading to the motor
- * Remove the worm gear by unscrewing it from the drive shaft
- * Replace the worm gear with a new one and reassemble the mixer
What Tools Are Needed To Replace The Worm Gear On A Kitchenaid Mixer
A KitchenAid mixer is a durable appliance that can last for many years. However, like all appliances, it will eventually need to be repaired. One of the most common repairs for a KitchenAid mixer is replacing the worm gear.
The worm gear is a small, toothed gear that is connected to the motor and drives the mixer’s mixing action. Over time, the teeth on the worm gear can wear down or become damaged, causing the mixer to stop working.
To replace the worm gear on a KitchenAid mixer, you will need a few tools. These tools include a Phillips head screwdriver, a socket wrench, and a worm gear replacement kit.
The worm gear replacement kit should include a new worm gear, a gasket, and any necessary screws. You will also need a grease gun to lubricate the worm gear and the mixer’s drive shaft.
To install the new worm gear, you will need to remove the mixer’s mixing bowl and lift the mixer’s head assembly off of the base. Then, remove the screws that hold the worm gear in place and lift the old worm gear off of the drive shaft.
Next, install the new worm gear by aligning the holes in the worm gear with the drive shaft and screwing the new worm gear into place. Then, replace the gasket and screw the head assembly back onto the base.
Finally, use the grease gun to lubricate the worm gear and the drive shaft, and then replace the mixing bowl. Your KitchenAid mixer should now be working like new.
How To Install The New Worm Gear In A Kitchenaid Mixer
To install the new worm gear in a KitchenAid mixer, follow these steps:
1. Unplug the mixer and disconnect it from the power source.
2. Remove the screws that hold the bottom plate in place.
3. Lift the bottom plate off and set it aside.
4. Locate the worm gear, which is the large gear that meshes with the pinion gear on the motor shaft.
5. Remove the old worm gear from the mixer.
6. Install the new worm gear by aligning it with the pinion gear and pressing it into place.
7. Replace the bottom plate and screw it back on.
8. Plug the mixer back in and turn it on to test it.
Note: It’s always a good idea to refer to the KitchenAid mixer’s user manual for specific instructions, as different models may have slightly different assembly procedures.
How To Test That The New Worm Gear Has Been Installed Correctly
To test that the new worm gear has been installed correctly, you can follow these steps:
1. Start by checking the worm gear for any damage or wear. If the gear is in good condition, it has been installed correctly.
2. Next, check the alignment of the worm gear. The gear should be aligned with the drive shaft and the teeth should be properly meshed.
3. To check the meshing of the gear, you can use a feeler gauge to measure the gap between the teeth. The gap should be consistent and there should be no missing teeth.
4. Finally, test the gear by rotating it by hand. The gear should turn smoothly and there should be no binding or grinding.
If everything checks out, the new worm gear has been installed correctly and is ready for operation.
How To Prevent The Worm Gear From Failing Again In The Future
To prevent the worm gear from failing again in the future, it is essential to identify the root cause of the problem. This can be done by conducting a thorough inspection of the worm gear, its components, and the surrounding machinery. Common causes of worm gear failure include excessive wear, improper lubrication, overloading, and misalignment.
To prevent excessive wear, it is important to regularly inspect the worm gear for any signs of damage, such as teeth wear, pitting, or corrosion. Any signs of damage should be repaired or replaced immediately. Additionally, it is important to ensure that the worm gear is properly lubricated with the correct type of lubricant. The type of lubricant used will depend on the type of worm gear and the environment in which it is used.
To prevent overloading, it is important to ensure that the worm gear is not subjected to loads beyond its rated capacity. This can be achieved by regularly checking the load on the worm gear and adjusting it if necessary.
To prevent misalignment, it is important to regularly check the alignment of the worm gear and its components. Misalignment can be caused by a variety of factors, such as thermal expansion, vibration, or improper installation. Any misalignment should be corrected as soon as possible.
By following these tips, you can reduce the risk of worm gear failure in the future and extend its lifespan.
Key Points
In conclusion, replacing your kitchenaid mixer worm gear is a relatively easy process that can be done in just a few minutes. Be sure to follow the instructions carefully and be careful not to lose any of the small parts. With a little bit of effort, your kitchenaid mixer will be back up and running like new.
